BBR-4MGを弄る(Linux)(第1回)BBR-4MGにシリアル接続してみる

昨日作ったケーブルを使って、バッファローのBBR-4MGにシリアル接続してみます
こんな感じで接続します↓

 

========関連記事========

今回、使用したケーブルは
赤、白→GND
緑→RXDへ
黒→TXDへ
と接続します。
シリアル接続する前に、Teratermのボーレートを115200にするのを忘れずに!!
↓起動すると以下のような画面が拝めます。
===========================================================
BUFFALO BBR-4MG Loader v1.80 build Dec 12 2003 10:13:58
Broad Net Technology, INC.
===========================================================
manu_id=6000 chip_id=401A
INTEL TE28F160C3-B bottom boot 16-bit mode found
Copying boot params…..DONE
Press any key to enter command mode …
Press Reset button to enter Tiny_ETCPIP_KERNEL …
Flash Checking Passed.
Unzipping program from bank 2…done
Try to find image for running…
Unzipping program from bank 3…doneABCDEFGHIJDRAM
STCK
MAIN
[FLOW] Main() Begin ….
[GPIO FLOW] SetGpio() Begin ..
[GPIO FLOW] SetGpio() End.
[FLOW] Main() before call initialize_data_area() ..
##### _ftext = 0x80001000
##### _fdata = 0x80141080
##### __bss_start = 0x80156034
##### end = 0x806D9754
##### Backup Data from 0x80141080 to 0x80709754
[FLOW] Main() afeter call initialize_data_area()
install_exception
sys_irq_init
memlib_init
hw5120cfg_init
ADMtek_GPIO_Init()
set GPIO 3 to output mode and enable with output value HI.
System startup…
soho initialize COLOR1 : 450000
manu_id=0089 chip_id=88C3
INTEL TE28F160C3-B bottom boot 16-bit mode found
Set flash memory layout to Boot Parameters found !!!
Bootcode version: v1.80
Serial number: S647002257
Hardware version: u眷
v1.80
sizeof(struct III_Config_t) is 75980
manu_id=0089 chip_id=88C3
INTEL TE28F160C3-B bottom boot 16-bit mode found
default route: 0.0.0.0
BufferInit:
BUF_HDR_SZ=32 BUF_ALIGN_SZ=0 BUFFER_OFFSET=96
BUF_BUFSZ0=384 BUF_BUFSZ1=1632
NUM_OF_B0=200 NUM_OF_B1=1100
BUF_POOL0_SZ=83200 BUF_POOL1_SZ=1830400
*BUF0=0x804d79a8 *BUF1=0x80318b98
Altgn *BUF0=0xa04d79b0 *BUF1=0xa0318ba0
End at BUF0:0xa04ebeb0, BUF1:0xa04d79a0
buffer0 pointer init OK!
buffer1 pointer init OK!
time = 01/01/2003, 00:00:00
Interface 0 ip = 127.0.0.1
ssmac_init begin ..
+Pafter my_if5120_init ..
if_adm51201: Ethernet address : 00 16 01 1c ed 26
time = 01/01/2003, 00:00:00
Interface 1 ip = 192.168.11.1
if_adm51202: Ethernet address : 00 16 01 1c ed 27
time = 01/01/2003, 00:00:00
Re-Init NAT data structure
Init NAT data structure
Interface 2 ip = 0.0.0.0
ruleCheck()> Group: 0, Error: Useless rule index will be truncated
ruleCheck()> Group: 1, Error: Useless rule index will be truncated
ruleCheck()> Group: 2, Error: Useless rule index will be truncated
ruleCheck()> Group: 3, Error: Useless rule index will be truncated
ruleCheck()> Classify Rule: 1, Error: Protocol Field
ruleCheck()> Classify Rule: 2, Error: Protocol Field
ruleCheck()> Classify Rule: 3, Error: Protocol Field
ruleCheck()> Classify Rule: 4, Error: Protocol Field
ruleCheck()> Classify Rule: 5, Error: Protocol Field
ruleCheck()> Classify Rule: 6, Error: Protocol Field
ruleCheck()> Classify Rule: 7, Error: Protocol Field
ruleCheck()> Classify Rule: 8, Error: Protocol Field
ruleCheck()> Classify Rule: 9, Error: Protocol Field
ruleCheck()> Classify Rule: 10, Error: Protocol Field
ruleCheck()> Classify Rule: 11, Error: Protocol Field
ruleCheck()> Classify Rule: 12, Error: Protocol Field
ruleCheck()> Classify Rule: 13, Error: Protocol Field
ruleCheck()> Classify Rule: 14, Error: Protocol Field
ruleCheck()> Classify Rule: 15, Error: Protocol Field
ruleCheck()> Classify Rule: 16, Error: Protocol Field
ruleCheck()> Classify Rule: 17, Error: Protocol Field
ruleCheck()> Classify Rule: 18, Error: Protocol Field
ruleCheck()> Classify Rule: 19, Error: Protocol Field
ruleCheck()> Classify Rule: 20, Error: Protocol Field
ruleCheck()> Classify Rule: 21, Error: Protocol Field
ruleCheck()> Classify Rule: 22, Error: Protocol Field
ruleCheck()> Classify Rule: 23, Error: Protocol Field
ruleCheck()> Classify Rule: 24, Error: Protocol Field
ruleCheck()> Classify Rule: 25, Error: Protocol Field
ruleCheck()> Classify Rule: 26, Error: Protocol Field
ruleCheck()> Classify Rule: 27, Error: Protocol Field
ruleCheck()> Classify Rule: 28, Error: Protocol Field
ruleCheck()> Classify Rule: 29, Error: Protocol Field
ruleCheck()> Classify Rule: 30, Error: Protocol Field
ruleCheck()> Classify Rule: 31, Error: Protocol Field
ruleCheck()> Classify Rule: 32, Error: Protocol Field
reqCBACBuf()> init match pool, Have: 1000
Memory Address: 0x8067b158 ~ 0x80681ed4
reqCBACBuf()> init timeGap pool, Have: 10000
Memory Address: 0x80681ed4 ~ 0x806b2c28
reqCBACBuf()> init sameHost pool, Have: 2000
Memory Address: 0x806b2c28 ~ 0x806c2648
[setClsfyEnable] clsfy_func=0
CBAC rule pool initialized !!
Init NAT data structure
RUNTASK id=1 if_task if0…
RUNTASK id=2 if_task if1…
RUNTASK id=3 if_task if2…
RUNTASK id=4 timer_task…
RUNTASK id=5 conn_mgr…
year=103,mon=0,day=1RUNTASK id=6 period_task…
RUNTASK id=7 dhcp_daemon…
RUNTASK id=8 dhcp_clt…on interface 2
RUNTASK httpd…
RUNTASK id=11 dnsproxy…
RUNTASK id=12 rip…
RUNTASK id=13 ripout…
RUNTASK id=14 pptp_callmgr…
RUNTASK id=15 dhcpd_mgmt_task…
UPnP is enabled
UPNP Device initialize success! slot=16
RUNTASK id=17 interrupt_read_task…
RUNTASK id=18 Receive_Server_Thread…
RUNTASK id=19 Alarm_Server_Task…
Starting Multitask…
MTstart2() begin …
RUNTASK id=0 period_task…
httpd: listen at 192.168.11.1:80
dnsproxy running…
IP_ADD_MEMBERSHIP: e0000009
[ripCreateSocket] join 224.0.0.9 on 127.0.0.1 ok!! [ifno=0] IP_ADD_MEMBERSHIP: e0000009
[ripCreateSocket] join 224.0.0.9 on 192.168.11.1 ok!! [ifno=1] dhcpd_mgmt_task started…
Receive_Server_Thread
1st seed=0xcce19a88
httpd: listen at 192.168.11.1:61182
HTTPD: add a listen port 61182 for UPNP
**** httpd_ready=1
[dhcp_clt] could not find DHCP daemon to get information
period_task running 60
Buf0: 198, Buf1: 845
[dhcp_clt] could not find DHCP daemon to get information

雑談スレ

日本語が含まれない投稿は無視されますのでご注意ください。(スパム対策)